Shopping for the best relay buddy pro test kit is about as tricky as finding your soulmate. You not only think about quality, price but also need to find where to buy relay buddy pro test kit. Don’t worry any more! We spend many hours to review and compare relay buddy pro test kit to make the short list for you. Let’s check which product is suitable with you.
Best relay buddy pro test kit
1. Electronic Specialties 193 Black 2.5" x 5" 12/24V Diagnostic Relay Buddy Pro Test Kit
Feature
Tests 5 different relays, both 12V and 24V and 3 diagnostic trouble codes help define the cause of the bad relayKit Includes 5 Relay Adapters and blow mold case
Quick off-the-car relay tester
Checks relay coil & switch contacts
Fails bad relays - Good/Bad indication, green light for PASS, red light for FAIL with flashing trouble code
Tests 5 different relays, both 12V and 24V
3 diagnostic trouble codes help define the cause of the bad relay
#193 Kit Includes 5 Relay Adapters and blow mold case
Quick off-the-car relay tester - checks relay coil & switch contacts
Description
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go/no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience. Relay Buddy 12/24 provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.2. Electronic Specialties 191 Relay Buddy Pro Test Kit
Feature
Kit includes Relay Buddy tester, 5 new relay adapters and blow mold caseRelay Buddy is a quick go/no go tester for the most common automotive relays
With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays
Relay Buddy will fail the relay and light the red LED if any of the test cycle proves unsuccessful during the test session; green light if relay is good
Settable to 4 and 5-pin relay and uses vehicle's 12 volts battery for power
Description
Relay Buddy, pro test kit.3. Lisle 69300 Master Relay Test Jump Set
Feature
Includes 8 Jumpers to fit most popular relaysIncludes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter
Terminal Leads with switch, fuse and power options provide easy access to check current or voltage on many fuses and relays used on vehicles today
Also allows testing of relay configurations not covered by eight Relay Test Jumpers, like Volkswagen, BMW and other European vehicles
Relay Puller Pliers easily remove electrical relays; weorks without piercing wires
Description
Kit Makes Testing Relays or Live Circuits Quick and Easy.4. Electronic Specialties 190 Relay Buddy Automotive Relay Tester
Feature
Quick off-the-car relay tester - checks relay coil and switch contactsAutomatic test with good/bad indication - fails bad relays
Settable to 4 and 5 pin relay - tests the 3 most popular automotive relays
Switch contact are loaded to detect excessive resistance
Uses vehicle's 12 Volt battery for power
Description
Relay Buddy is a quick go/no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay buddy will fail the relay and light the red LED if any one of the cycles proves unsuccessful during the test session.5. Lisle 56810 Relay Test Jumper Kit
Feature
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles; simply remove relay to be tested, insert correct jumper and insert relay into jumperWhen using green four pin jumper be careful to align pins on jumper and relay correctly
Jumpers have tabs for clamping and flat pads to place test leads on
Set comes in blow-molded case for storage
No need to pierce wires or connect multiple jumper wires
Description
Set of Four Relay Test Jumpers Make Testing Relays or Live Circuits Quick and Easy.6. Universal 12V Car Relay Tester Checker Diagnostic Tool with Alligator Clips
Feature
Made of high quality ABS plastic, sturdy and durable. Working temperature: 0-50 (C).Detector will observe the contact head data, closing time, each test phase of the relay inertia and so on.
Relay test: If the bright red LED, it means that the status is abnormal, if the bright green LED, it is normal.
Provides a convenient and intuitive diagnostic way, time-saving and save money.
Car battery must be 12V battery, the voltage must be between 11-15V. The coil resistance is preferably at least 20 ohms.
Description
Specifications:- Material: ABS
- Size: 115 x 66 x 23mm
Instructions:
- 1. Connect the power leads to the car battery -- black alligator clip to negative terminal, red alligator clip to positive terminal.
- 2.Tester is powered up when the LED illuminates in RED.
- 3. Check the relay before plugging into the tester. If it's a 4 pin relay, select "4 pin" on the tester. If it's a 5 pin relay, select "5 pin" on the tester.
- 4. Plug in the relay into one of the three receptacles.
- 5. Press the "Test" button.
- 6. Tester will check the pin configuration of the unknown relay. Tester will light the RED LED if the unknown relay is not the same to the most of common automotive relays or the pin of the unknown relay is destroyed.
- 7. Tester will open and close the relay 10 times for testing the time to contacts closure and opening if the pin configuration of the relay is right. Tester will light the RED LED immediately if the time is overtime.
- 8. Tester will check the consistency of the relay after testing the time to contacts closure and opening ten times. Tester will light the GREEN LED if the test passed, if not light the RED LED.
- 9. Disconnect power leads from the car battery and remove relay from the tester.
- Package content:
- 1 x Car Relay Tester
7. Electronic Specialties 191 Relay Buddy Pro Test Kit by Electronic Specialties
Feature
Kit includes Relay Buddy tester, 5 new relay adapters and blow mold caseRelay Buddy is a quick go/no go tester for the most common automotive relays
With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays
Relay Buddy will fail the relay and light the red LED if any of the test cycle proves unsuccessful during the test session; green light if relay is good
Settable to 4 and 5-pin relay and uses vehicle's 12 volts battery for power
Description
Relay Buddy Pro Test Kit8. Lisle 60660 Deluxe Relay Test Set
Feature
Jumpers have tabs for clamping and flat pads to place test leads onAlso includes test lead kit for easily and securely connecting relay test jumpers to a multimeter
No need to pierce wires or connect multiple jumper wires
Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage
Also provides access for a clamp-on ampere meter
Description
Includes 8 jumpers to fit most popular relays. Also includes test lead kit and relay puller pliers. Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also includes test lead kit for easily and securely connecting relay test jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay puller pliers easily remove electrical relays without damage to the relay or electrical box.9. Electronic Specialties 192 Black 2.5" x 5" 12/24V Diagnostic Relay Buddy
Feature
Tests both 12V and 24V relays3 diagnostic trouble codes help define the cause of the bad relay
Quick off-the-car relay tester
Checks relay coil & switch contacts
Fails bad relays - Good/Bad indication, green light for PASS, red light for FAIL with flashing trouble code
Description
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience. Relay Buddy 12/24 provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.10. Relay Pro Universal Automotive Relay Tester [12 Volt Relay Tester] Tests 4 & 5 Pin Relays - Made in The USA
Feature
EASY TO USE: Quickly [ Pass - Fail ] tests most 12 Volt DC car and truck relaysUNIVERSAL RELAY TESTER: Tests a broad range of 4 & 5 pin automotive relays
FLEXIBLE CLIP SYSTEM: Not limited by adapters found in other relay testers
AUTO CONFIGURATION: Clips are not numbered, connect any clip to any relay pin
NO BATTERIES NEEDED: Uses the car or truck battery
Description
The Relay Pro is a simple automotive relay tester that will easily and quickly test most 12 Volt DC truck and car relays.
The Relay Pro tests relays by simply clipping the test leads onto the relay terminals (pins) thus eliminating the need for specific tester footprints or adapters.
The Relay Pro tests relays by automatically determining how the relay is configured.
If you are testing a 4 pin Relay, set the tester to Number of Pins 4, or if testing a 5 pin relay set the Number of Pins to 5.
Once the Relay Pro has determined the correct configuration of the attached relay it will begin to operate the relay coil and check for the proper reaction from the relays contacts.
The Relay Pro injects about a 1 Amp test Current through the relay contacts to accurately check for Voltage drop across the contacts.
The Relay Pro will then continue checking for proper operation of the relay through a series of 10 operations.
If any of the tests fail, then the testing will stop and the red Fail LED will light. If all 10 testing operations are successful, the green Pass LED will light.