What are criterias of the best volume pot 1 meg? It is not easy to find the answer. We spent many hours to analyst top 10 volume pot 1 meg and find the best one for you. Let’s find more detail below.
Best volume pot 1 meg
1. Fender Pure Vintage 1 Meg Solid Shaft Control Potentiometer
Feature
Vintage-accurate 1 Meg linear 3/8" solid shaft potentiometer; used for volume or tone controlsIncludes mounting nut and washer
Used on vintage and modern Jaguar and Jazz master guitars
Fits most Jaguar, Jazz master and hum bucking pickup-equipped Telecaster guitars
Description
Fender offers a wide selection of Pure Vintage electronics to players looking to restore or upgrade their guitar or amplifier with classic Fender in mind. From potentiometers to select capacitors, tube sockets and more, these electronics are created to closely replicate original-era Fender parts and have been used on a number of Fender reissue instruments and amplifiers, including our American Vintage series of guitars and basses. But best of all, Pure Vintage guitar and amp electronics are also versatile enough to fit most Fender guitars and tube amplifiers, making it easier than ever to inject that vintage vibe into any setup.2. Allparts CTS 500K SHORT Split Shaft Audio Taper Potentiometer
Feature
500K ohm resistanceAudio Taper
Suitable for use as volume or tone pot
3/8" bushing diameter X 3/8" height. Suitable for through body mount, not for guitars with control plates.
Not suitable for import guitars
Description
CTS 500K short shaft (3/8" bushing height) potentiometer. Audio taper suitable for either tone or volume controls. Not intended for use in import guitars that use metric components3. 10 Bulk Pack Genuine CTS Tone/Volume 1Meg Split Shaft Pots for Electric Guitar
Feature
1 MegAudio taper
Split Shafts (for compression fit knobs)
3/8' shafts
Washers and nuts included
Description
electric-guitar-replacement-parts4. 3 Bulk Pack Genuine CTS Tone/Volume 1 Meg Split Shaft Pots for Electric Guitar
Feature
1 MegAudio taper
Split Shafts (for compression fit knobs)
1/4' shafts
Washers and nuts included
Description
electric-guitar-replacement-parts5. Alpha Potentiometer, 1Meg Audio (Log)
Feature
Guitar Amp Potentiometer. 1MA / 1 Meg Ohm / 1 Meg Audio / 1M Log / 1,000,000 ohmsFits 3/8" Hole
1/4" Solid Shaft
24mm Body, Solder Lugs, 1/2 Watt Rated, 300 Rotation, 250VDC Rated, Carbon Composition
Comes With Hex Nut and x2 Washers
Description
Guitar Amp Potentiometer. Audio/Log pots are typically used for volume control, and Linear pots are typically used for effects. 1MA / 1 Meg Ohm / 1 Meg Audio / 1M Log / 1,000,000 ohms. Fits 3/8" Hole. 1/4" Solid Shaft. 24mm Body, Solder Lugs, 1/2 Watt Rated, 300 Rotation, 250VDC Rated, Carbon Composition. Comes With Hex Nut and x2 Washers6. Fender Pure Vintage 250K, Solid Shaft Potentiometer
Feature
Genuine Fender Replacement PartHigh Quality
Durable
Description
250K, Solid Shaft Potentiometer7. Alpha Control Pots for Electric Guitar, 1 meg-ohm - 4 Pack
Feature
Alpha potentiometers are among the world's most widely used guitar tone and volume controlsAlpha pots are audio taper with standard +/- 20% resistance tolerance
1-meg pots attenuate even less than 500K-ohm pots-try one if you want to hear your guitar "wide open"
Each pot has an aluminum split shaft that fits a coarse-knurled (18-spline) knob
Contains 4 pots; each pot comes with a flat washer, lock washer, and two hex mounting nuts
Description
SAVE WHEN YOU BUY A 4 PACK!
Great price!
Alpha potentiometers are among the world's most widely used guitar tone and volume controls. Each pot has an aluminum split shaft that fits a coarse-knurled (18-spline) knob.
Get the most out of your guitar with a 1 Meg-ohm pot. All pots bleed a certain amount of the signal to ground, this "attenuation" can be used to warm the sound of your guitar's pickups, but you can also run your guitar "wide open" with these 1 Meg-ohm pots
Shaft diameter: 6mm split shaft, coarse knurling
Thread: M8 x 0.75
Threaded portion height: 3/8" (9.52mm)
Required mounting hole diameter: 5/16" (7.94mm)
Alpha pots are audio taper with standard 20% resistance tolerance. Each pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard or control plate.
Which pot value should you choose?
500K pots are standard controls for humbuckers, and 250Ks are usually used for single-coil pickups. A 250K gives a slightly warmer tone than a 500K, and bleeds off some of the high frequencies to ground. A 1-meg pot bleeds off even less than a 500K-try one if you want to hear your guitar "wide open."
1-meg pots are also ideal for piezo pickups, as the ultra high impedance piezo element is more adversely effected by conventional, lower-value pots than magnetic pickups.
25K pots are for controlling the volume or tone of active pickups, or for use after the preamp of a piezo-saddle transducer bridge.
8. Wd 1 Meg Pot
Description
1000k-ohm audio taper, full size pot. Used in vintage Tele and Jazzmaster guitars for volume controls. Also recommended for maximum gain on high output pickups , 24 MM DIA. 3/8-32 thread, 24 spline, 20% tolerance, 3/8 shaft length 3/8 bushing height.9. bangdan Split Shaft Audio Taper Potentiometer Pot US Fine Spline, CTS 1meg ohm Audio Taper
Feature
CTS 1 Meg Split Shaft Audio Taper Potentiometer Pot US Fine Spline.***Fast delivery.***Description
Genuine CTS control pot.
1meg ohm Audio Taper.
3/8" diameter mounting shaft.
Fine spline split shaft (approx. 20 splines).
Includes nut and washer.
See images for detailed pot measurements.
***Fast delivery.***
10. Metallor Push Pull Pot DPDT Switched Guitar Bass Potentiometer Audio Volume Tone Split Shaft Control Switch 18mm with Nuts and Washers Guitar Parts Replacement (A250K)
Feature
A250 kOhm logarithmic taper potentiometer with Double Pole Double Throw ( DPDT on-on ) push / pull switch. 6mm splined shaft to accept standard push on control knobs.This switched pot is suited to being used in place of the standard tone pot, although it is personal choice whether you use these taper pots for volume or tone, on a single coil equipped guitar to provide tonal switching options. Typical uses include phase reversal, tone capacitor switching, tone bypass etc.
Shaft length: Approx. 18mm shaft diameter: Approx. 6mm Whole length: Approx. 45mm Base diameter: Approx. 22mm
Full size; Coarse knurled split shaft fits most control knobs
Package included: 1pc potentiometer, Supplied with 2 x mounting nuts and 1 washer.
Description
250K VS 500K
Generally, 500K-ohm pots are used with humbuckers and 250Ks are used with single-coil pickups. You can use any value you like, but a 250K will give a slightly warmer tone than a 500K pot. The 250K pot bleeds off some of the high frequencies to ground. A 1 Meg-ohm pot bleeds off even less than a 500K pot, so if you want to hear your guitar "wide open" you may want to try one.
Product Description:
For bass guitar mainly
Push pull switch pots
A250k resistance
A type tone style
Approx. 18mm long shaft
Full resistance: 250k ohm
Shaft Diameter: Approx. 6mm
Whole length: Approx. 45mm
Base size: Approx. 22mm
Knurled and split shaft
Package Included:
1pc guitar bass pot, comes with nut and washer