It's hard to know which is good betafpv flight controller osd frsky. There are alot of betafpv flight controller osd frsky reviews on internet. In this article we suggest top 10 the best betafpv flight controller osd frsky for you. Please read carefully and choose what is the best betafpv flight controller osd frsky for you.
It’s hard to know which is good betafpv flight controller osd frsky. There are alot of betafpv flight controller osd frsky reviews on internet. In this article we suggest top 10 the best betafpv flight controller osd frsky for you. Please read carefully and choose what is the best betafpv flight controller osd frsky for you.
Best betafpv flight controller osd frsky
1. BETAFPV F4 1-2S FC AIO Brushless Flight Controller SPI Frsky Receiver ESC OSD Smart Audio with JST-PH2.0 Cable for 2S Brushless FPV Whoop Drone Beta85 Pro2 Beta75 Pro2 Beta65 Pro2
Feature
Betafpv AIO F4 FC is highly integrated with a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC, suitable for a lighter 2S whoop drone, like Beta65 Pro 2 or Beta75 Pro 2 etc. So the 2S drone could save much weight for a faster fly experience.The 2S F4 FC AIO Brushless Flight Controller comes with a SPI Frsky receiver, binding procedure is easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000049912-f4-1s-brushless-fc-manual
The power supply is 1S~2S, it comes with a 2S cable pigtail JST-PH 2.0 connector in default, customer can use 2pcs 1S 300mAh battery work on this. If you want to use it with 2S battery, please change the cable to XT30 : www.amazon.com/dp/B07FFQ2TXQ
The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be seted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.
This AIO F4 2S FC also can be used on 2S brushless whoop drone Beta75X and Beta65X, performance very well even no wash-out issue then, so you can just take this AIO FC to replace the stock FC&ESC.
Description
BETAFPV 2S F4 FC AIO Brushless Flight Controller SPI Frsky Receiver ESC OSD Smart Audio with JST-PH2.0 Cable for 2S Brushless FPV Whoop Drone Beta75 Pro 2 Beta65 Pro 2 Beta75X Beta65X
Bind procedure:
a. Power on the board by connecting the battery or USB power. Then the green receiver LED start to flash.
b. Click the bind button for 3s. Then the green receiver LED will be solid on.
More details checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000049912-f4-1s-brushless-fc-manual
Specification:
Item: F4 2S AIO Brushless Flight Controller (Frsky RX+OSD+ESC)
FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the Beta65X frame and Beta75 Pro frame.
Firmware version: betaflight_matekf411rx_4.0.0 (Development Version)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Built in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol.
Power Cable: 55mm, with 2pcs JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4.5g
ESC
Built-in ESC with 5A continuous and peak 6A current
Power supply: 1-2S
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Package
1 * F4 2S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
2. BETAFPV F4 Brushed Flight Controller Integrated with OSD and Frsky Receiver
Feature
The world's first compatible BetaFlight OSD, FrSky Rx, BetaFlight firmware, born for acro flight controller for the Micro Whoop or Blade Inductrix quadcopter.Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
Built in SPI Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module.
Designed to work with current Tiny Whoop or Blade Inductrix setups.
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
BETAFPV F4 Brushed Flight Controller Integrated with OSD and Frsky Receiver for Tiny Whoop Drone.
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, SPI Frsky Rx, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Specifications:
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D8 protocol (AKA FRSKY_D on Betaflight Configuration)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g
Tips:
How would do an OSD with the AIO cameras?
There is a video in and out on the fc itself, labeled CAM and VTX as show below. There should be a video in and out on the AIO camera, like BETAFPV H02 etc. If not, you would have to modify the camera for sure but it would totally be worth it. There is some examples:
BETAFPV H02 or other AIO cameras with video in and out available.
FX806 or other AIO cameras with camera and vtx are connected with cables.
Other regular AIO cameras like VM275, FX805, Eachine XT02 etc.
BETAFPV Support Freshdesk for BetaFlight OSD Setup:
https://betafpv.freshdesk.com/support/solutions/articles/27000038661-betaflight-osd-setup
Package:
1 * F4 OSD brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
3. BETAFPV F4 V3 2-4S AIO Brushless Flight Controller No RX BLHELI_S 12A ESC OSD Smart Audio with XT30 Cable for Beta85X Beta75X Beta75 Pro 2 Brushless Whoop Drone
Feature
Built-in Current MeterThis F4 2-4S AIO FC V3 version has a built-in current sensor, you could get a more accurate current value without the virtual current meterCautions when using 4s batteryThis F4 AIO FC can really support 4S battery. But please don't use motors with too high KV value or poor quality. No 0x0x/1102/1103 series motors could stand 4S power for the moment in the market
Integrated FC with light weight Only weighs 5.6g integrated with a Betaflight MATEKF411 processor FC, Betaflight OSD and 2-4S 12A ESC which can support 4S battery for fast flying experience
Supported ReceiverThe F4 2-4S AIO FC Brushless Flight Controller builted without receiver, please note it only Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Also support Frsky R9M Receiver and DSMX receiver since V1.2. Compatible receivers signal include PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Battery & Motor comboHighly recommend the 1103 11000KV / 0802 12000KV / 08028 12000KV Motor for setting 2s kit. 1103 8000KV / 1105 6000KV Motor will be the best choice for 3S kit. If you try it on 4S kit, we suggest you to use the 1105 5000KV Motor
Description
Specifications of FCCPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/TBS Crossfire Receiver/Frsky R9M Receiver/DSMX receiver
Support programmable LED like WS2812 etc
Weight: 5.6g
Specifications of ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 13A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7
Recommended Motors:
2S: 1103 11000KV Motor-www.amazon.com/dp/B07FN64599
3S1103 8000KV / 1105 6000KV Motor-www.amazon.com/dp/B07MZ2BSDT
4S1105 5000KV Motor
Could the ESC on this AIO board support really 4S battery?
Yes. But please pay more attention to the motors. Here are two situations that the motor will burn itself and then the ESC frequently.
Situation 1:
The motor's KV value is too high and could not stand the 4S power. For example, the BETAFPV 1105 6000KV motors could not stand the 4S power in aggressive flying. So we are working on a lower KV 1105 motor that could use with 4S battery. It will be released soon.
Situation 2:
A poor quality motor will result in the fire accident in 4S power. No 0x0x/1102/1103 motors could stand 4S power for the moment in the market. Please make sure your motors could support the 4S battery before any try.
PACKAGE:
1 * F4 2-4S brushless flight controller with XT30 Plug
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
4. BETAFPV F4 1S Brushless Flight Controller V2.1 Frsky Receiver 5A ESC with JST-PH2.0 Connector for FPV 1S Brushless Tinywhoop Micro Whoop Drone FPV Like Meteor65 Beta75Pro Beta65Pro Quads
Feature
Suitable for 1S droneSpecially made for 1S brushless whoop with F411 chip. The vtx power supply is changed from vbat to 5v. Recommended to use our lightest M01 AIO camera. It's a great choice for building Beta65 Pro and Beta75 Pro2.69g ultra lightweightThis is the lightest F4 1S brushless FC with slim and sleek design, only weight 2.69g without connector, which has better performance on function for maximum weight savings, power, and responsiveness Equips with solid connector, which can provide more stable and powerful current
JST-PH 2.0 solid connectorPre-soldered 60mm power cable pigtail with solid JST-PH 2.0 connector which can provide more stable and powerful current, also pre-flashed with Betaflight firmware, just bind and play
Frsky binding settingsThe default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be set as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode
Technical supportPlease kindly contact us on Amazon or by Email [email protected] before negative comment or return, we will provide technical support to solve all your product issues. Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 1S Brushless Flight Controller V2.0 Frsky Receiver 5A ESC OSD Smart Audio with Ph2.0 Solid Connector for FPV 1S Brushless Tinywhoop Micro Whoop Drone FPV like Beta75Pro Beta65Pro QuadcopterSPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 29mm x 29mm, fully compatible with the whoop frame in the current market, Beta65 Pro frame, Beta75 Pro frame, BWhoop B06 frame, and mounting pattern
Firmware version: Betaflight MATEKF411RX (MK41R)
Compatible with Z02, A01, M01 VTX
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 60mm, with JST-PH 2.0 connector, 1.25mm motor header pins
Receiver: Frsky
Smart Audio
Weight: 2.69g
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
RECOMMENDED PARTS
Frame:
Beta65 Pro frame -- www.amazon.com/dp/B078GLW4HK
Beta75 Pro frame --www.amazon.com/dp/ B078H7R3PV
Props:
31mm 4-Blades props (for Beta65 Pro frame) -- www.amazon.com/dp/B075F8DM26
40mm 4-blades props (for Beta75 Pro frame) -- www.amazon.com/dp/B07B2P7TF4
Camera:M01 AIO camera -- www.amazon.com/dp/B07X96YBJT
Battery: 300mAh 1S Battery --www.amazon.com/dp/B07FFTVB8C
PACKAGE 1 * F4 1S brushless Frsky FC V2.1
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
1 * JST-PH 2.0 solid connector
5. BETAFPV F4 FC 2S-4S Brushless Flight Controller and BLHeli_32 16A ESC OSD Smart Audio No Receiver with XT30 Cable for Brushless FPV Micro Drone Cine Whoop Beta85X
Feature
This combo of F4 FC with BLHeli_32 16A ESC built-in BetaFlight OSD is customized for Cine whoop drone Beta85X. Please note: When you connect the receiver to this FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.BLHeli_32 is the 3rd generation ESC firmware after BLHeli and BLHeli_S, which is written for ESC' s that utilize 32-bit MCU. With the increase in processing power, faster input signals with lower latency and higher update rate would be possible in BLHeli_32, such as Dshot1200.
Firmware version of F4 FC is Betaflight OMNIBUSF4SD (OBSD), built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support TBS micro receiver with TX02, RX02 ports. RSSI ports is available.
This ESC support BLHeli_32 suite pass-through ready, Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200. It can fit motors with 1.5mm header pins connector like 1105,1103 motors etc, and you can use it work with 450mAh 3S battery or 450mAh 4S battery.
Please note this F4 2S-4S FC is built without receiver, all the ports are available on this board. So that you could connect any receiver you want on the board. Such as Frsky XM/XM+ Receiver, TBS receiver and DSMX receiver. Receiver Connection: https://betafpv.freshdesk.com/support/solutions/articles/27000049913-f4-2s-brushless-fc-esc
Description
BETAFPV F4 FC 2S-4S Brushless Flight Controller and BLHeli_32 16A ESC OSD Smart Audio No Receiver with XT30 Cable for Brushless FPV Micro Drone Cine Whoop Beta85X
SPECIFICATIONS
F4 FC
The F4 FC board is the same one on Beta75X drone - www.amazon.com/dp/B07H8XQ7R6
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
TX02RX02 ports is available, so that it could support TBS micro receiver
RSSI ports is available
Buzzer solder pads
Support programable LED like WS2812 etc
Weight: 2.7g
BLHELI_32 16A ESC
Support BLHELI_32
Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 2S-4S lipo
Cotinue current: 16A
Peak current: 35A
Firmware target: BETAFPV-16A-32bit
MCU:STM32F051
Motor Connectors: 1.25mm header pins connector
RECOMMENDED PARTS LIST
Frame: Beta85X frame
Motors: 1105 motors / 1103 motors with 1.5mm header pins connector
Battery: 450mAh 3S battery / 450mAh 4S battery
PACKAGE
1 * F4 brushless flight controller
1 * 4in1 16A ESC board
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
6. BETAFPV F4 20A AIO 2-4S Brushless Flight Controller No RX FC BLHELI_S 20A ESC OSD Smart Audio with XT30 Cable for Brushless Micro Quadcopter FPV Racing Whoop Drone Like Beta85X CineDrone
Feature
Support&WarrantyIf there is anything problem with your BETAFPV item, please contact us before returning or refund. We will help you solve it at the first timeF4 AIO 20A Whoop FC F4 AIO 20A FC is the first 20A AIO flight controller in the market. Can totally handle 20A continuous current
Integrated FC with Light WeightIntegrated with a Betaflight MATEKF411 processor FC, Betaflight OSD, F4 MCU, and 20A ESC. The thickness of F4 1-4S AIO 20A FC from 1.6mm to 1.2mm, which reduces the weight to 5.63g while improving the ability of the ESC to continuous current 20A
Compatible Drone&MotorsWith standard 26.5x26.5mm mounting holes for easy installation in most whoop frames like Beta85X frame. Compatible with 120X130X140X brushless motors, supports 1-4S batteries. You can DIY Beta85X racing drone with this powerful FC to save weight
Supported ReceiverThe F4 1-4S AIO 20A FC Brushless Flight Controller builted without internal receiver, but supports external Frsky XM/XM+ Receiver/ DSMX Receiver / Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Compatible receivers signal include PWM, Oneshot125, Oneshot42, Dshot150, Dshot300, Dshot600
Description
BETAFPV F4 20A AIO 1-4S Brushless Flight Controller No RX BLHELI_S 20A ESC OSD Smart Audio with XT30 Cable for Brushless FPV Micro Quadcopter Racing Whoop Drone like Beta85XSPECIFICATIONS OF FC
CPU: STM32F411CEU6 (100MHZ)
Six-Axis: MPU6000 (SPI connection)
Size: 32.5*32.5mm (26.5mm mounting holes)
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
Support programmable LED like WS2812 etc
Built-in current sensor
Weight: 5.63g
SPECIFICATIONS OF ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 1-4S Lipo
Continuous current: 20A
Peak current: 25A
Firmware: BLHELI_S
Motor Connectors: 1.25mm header pins connector
RECOMMEND PARTS:
Motor:
1204 5000KV motor - www.amazon.com/dp/B07Z3RMH91
Batteries:
1S: 300mAh 1S Battery - www.amazon.com/dp/B07FFTVB8C
2S: 350mAh 2S Battery - www.amazon.com/dp/B07JG3ZFC5
3S: 300mAh 3S Battery - www.amazon.com/dp/B07WH1VRP1
4S: 450mAh 4S Battery - www.amazon.com/dp/B07RZ6PQPH
PACKAGE
1 * F4 1-4S AIO 20A Brushless Flight Controller with XT30 connector pre-sordered
4 * M1.2x4mm Screws
4 * M1.4x5mm Screws
4 * Anti-vibration Rubber Dampers
7. BETAFPV F4 Brushed Flight Controller FC with Betaflight OSD (No Receiver) for Micro Whoop Blade Inductrix Quadcopter
Feature
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
30A continuous drain current MOSFET. Lower to 8.5m inner resistance value (4.5V). It has a noticeable power improvement in low battery voltage status or with 8x20/8.5x20 motors.
No receiver integrated. So pilots could connect any receiver, like the TBS crossfire rx etc.Designed to work with current Tiny Whoop or Blade Inductrix setups
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
BETAFPV F4 Brushed Flight Controller FC with Betaflight OSD (No Receiveer) for Micro Whoop Blade Inductrix Quadcopter
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Here share you a introduction and flight video made by a keen customer:
https://youtu.be/M5p2kJGLscU
Specification
Item F4 Brushed FC No RX with OSD
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g
Package:
1 * F4 OSD brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
8. BETAFPV FPV FC Lite 1S Brushless Flight Controller SPI Frsky D8 Rx Compatible with Silverware Firmware JST-Ph2.0 Powerwhoop for Tiny Whoop Quadcopter FPV 1S Whoop Drone
Feature
Upgrade LiteOSDBulit-in OSD, which upgraded to use UART, the screen refresh rate is improved, make the screen data more stable. It allows you to select viewing options, such as voltage of battery, flight time, flight mode and setting menu. Includes OSD menu, supports PID tuning, motor rotation changing and channel mapping of AETR/TAER switching via OSD menuBuilt-in SBUS receiverBuilt-in Frsky D8 native receiver, supports SBUS and DSMX protocol, including Frsky xm / xm+ receiver, Futaba receiver, Crossfire receiver in SUBS mode and DSMX receiver
Lite 1S Brushless FCThe first 1S brushless Lite FC with Silverware Firmware, CPU has been updated to STM32F042G6U6 from STM32F030F4P6, totally support Smart Audio, highly recommend M01 AIO Camera with this FC for a great performance
More stable in Angle ModeThis 1S Lite Brushless FC solved the problem that the whoop drone will drift in the Angle Mode so the flight will be more stable. This is the best flight control for beginners
Technical SupportIf there is anything problem with your BETAFPV item. Please contact us by Email [email protected] before returning or refund. We will help you solve it at the first time
Description
BETAFPV FPV FC Lite 1S Brushless Flight Controller SPI Frsky D8 Rx Compatible with Silverware Firmware JST-Ph2.0 Powerwhoop for Tiny Whoop Quadcopter FPV 1S Whoop DroneSPECIFICATION OF FC
CPU: STM32F042G6U6
Six-Axis: MPU 6050
Mounting holes size: 26mm*26mm
Firmware: Silverware
OSD: LiteOSD
Built-in Receiver: Frsky D8
Support Receiver: SBUS and DSMX protocol receiver, including Frsky xm / xm+ receiver, Futaba receiver, Crossfire receiver in SUBS mode and DSMX receiver
Smart Audio
Weight: 3.34g with connector
SPECIFICATION OF ESC
Input Voltage: 1S
Continuous Current: 5A
Peak Current: 6A
Factory Firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600
Motor Connectors: 1.25mm header pins connector
Support BLHeliSuite programmable
Processor Chip: EFM8BB10
RECOMMEND PARTS:
Motor:
0802 22000KV -- www.amazon.com/dp/B07ZQH4R34
0603 19000KV -- www.amazon.com/dp/B079HXLJJ5
Battery:
300mah 1s Lipo Ph2.0 -- www.amazon.com/dp/B07FFTVB8C
Camera:
M01 AIO Camera -- www.amazon.com/dp/B07X96YBJT
PACKAGE:
1 * BETAFPV 2S Lite brushless flight controller
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Eachine black E010 frame / 75mm / 85mm frames)
4 * H0.8mm Anti-vibration rubber dampers
9. Beta65S BNF Micro Whoop Quadcopter Integrate with OSD Frsky Receiver with 17500KV 7x16mm motors
Feature
Beta65S BNF Micro Whoop Quadcopter Integrate with OSD Frsky Rx Version with 17500KV 7x16mm motorsMore punch on throttle with faster 17500KV 7x16mm motors and 3-blade propellers.
Receiver version: Frsky Rx, Firmware version: Betaflight BETAFLIGHTF3
BETAFPV Z01 aio 25mW vtx camera with 48 channels in total.
Great alternative to popular regular Tiny Whoop quadcopter.
Description
Beta65S BNF Micro Whoop Quadcopter Integrate with OSD Frsky Rx VersionSpecification:
Wheelbase: 65mm
Weight: 25g (without battery)
Flight Controller: BETAFPV F3 Brushed FC with native OSD and Frsky Rx
Firmware version: Betaflight BETAFLIGHTF3
Motor: 17500KV 7x16mm Motor
Receiver: Frsky D8 potocol with PA/DSMX/Flysky rx with AFHDS 2A protocol
Camera: AIO 520TVL 1/4 Inch Cam with 5.8G VTX 25mW 48CH
Power connector: JST-PH 2.0 connector, AKA PowerWhoop connector
Battery: 3.7V 230mAh Lipo battery
Flight time: 3min 30second
FC W/OSD: www.amazon.com/dp/B074GXKKZ7
Beta65S frame:www.amazon.com/dp/B074MTNKPL
7x16 motors: www.amazon.com/dp/B074MWWQHD
Package:
1 * Beta65S Micro FPV Quad
1 * BETAFPV 230mAh 1S Lipo Battery
10. BETAFPV Beta75X HD Frsky 3S Brushless Whoop Drone with F4 AIO 12A FC Turtle V2 Camera OSD Smart Audio 1103 8000KV Motor XT30 Connector for Micro Quadcopter FPV Racing
Feature
Support 3S with 2-4S AIO FCComes with updated BETAFPV F4 2-4S AIO 12A FC, can safely support Beta75X HD to 3S batteryTurtle V2 camera for HD DVRBeta75X HD whoop Drone equipped with Caddx Turtle V2 1080p 60fps mini HD FPV camera, brings you a HD vision and a more enjoyable flight experience
Updated 1103 8000KV motorUpdated 1103 motor 11000KV to 8000KV, which is customized for 3S lipo, highest speed increased obviously with this motor. It will give you a extreme power and speed
Recommend batteryHighly recommend the newest high quality 300mAh 3S 45C battery for Beta75X, it can provide high quality, reliable power. Please note the frame of Beta75X needs to be modified by removing the 3 sticks in order to fit 300mah 3S lipo. Please refer to the sixth picture for more details
Frame&PropsDurable and light black frame is customized for Beta75X HD. Washout issue almost doesn't exist with BETAFPV&Gemfan 40mm 4-blade 1.5 mm shaft propellers
Description
Please noteThis package of Beta75X HD don't include battery. Now we highly recommend BETAFPV 300mah 3S battery for the drone. But the frame needs to be modified if you use our 300mah 3s battery on Beta75X. Please refer to the picture for more details.SPECIFICATION
Weight: 57.4g (without battery)
Motors: 1103 8000KV Brushless motor
Props: 40mm 4-blades props, 1.5mm shaft hole
HD DVR Camera: CADDX Turtle V2
Turtle V2 Canopy: Canopy for Beta75X (HD DVR)
Receiver: Frsky FCC
FC SPECIFICATIONS
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
ESC SPECIFICATIONS
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 13A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Turtle V2 Camera
Camera angle: 30 no adjustable
Aspect Ratio: 4:3(non-changeable)
Image sensor: 1 / 2.7" CMOS sensor
Rating: 800TVL
TV system: NTSC
Video resolution: 1080P @ 60fps / 1080P @ 30fps / 720 @ 60fps
FPV FOV: 155
Record field of view: 170C
A01 VTX
Output power: 25mW and 200mW (Adjustable)
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Recommend Parts
F4 2-4S AIO 12A FC -- www.amazon.com/dp/B07RL29PNN
1103 8000KV Motor -- www.amazon.com/dp/B07SFJ1V6D
Beta75x HD Frame kit -- www.amazon.com/dp/B07RZPBY5G
300mAh 3S battery -- wwww.amazon.com/dp/B07SN32G8C
PACKAGE
1 * Beta75XHD3S Quadcopter (without battery)
4 * 40mm 4-blades props (2CW+2CCW)